Hook up car amplifier

hook up car amplifier

How to connect a car stereo to a car AMP?

Connect the remote power wire from the stereo to the amp, and the RCA cable is also connected here. After the set, the RCA to the head unit and remote power wire to the amp set the speaker wire to the speaker of your car.

Where should I install an amplifier in my car?

Good locations to install an amplifier include: Pros: You can use short wires and patch cords. You wont have to remove a seat or climb into the trunk. Cons: Only very small amps fit here. This puts your amp close to some common noise sources. Pros: Plenty of room for large amps. Near the rear speakers. Easy access to the amp controls.

How to connect RCA speaker to car amplifier?

After the set, the RCA to the head unit and remote power wire to the amp set the speaker wire to the speaker of your car. When you will get your RCA attached to the head unit and speaker wire, and ground cable and the main power cable on the carpet, hook the amplifier and turn on.

How to connect a car amplifier to a 12V power supply?

Unscrew the 12V screw, put the other end of the wire in the 12V port and tighten the screw. Now, when you have connected the remote wires with the power wires, you must connect the power wires in the power input port of the car amplifier. To do so, take the yellow wire and insert it in the 12V port.

Can you plug a car AMP into a car stereo?

Car stereos aren’t designed to be bridged like a car amp. Using an ATX (desktop computer) power supply for a car stereo isn’t hard – in fact, you only need a few steps: Power connections: Cut a +12V wire (yellow) and a ground (black) wire from the main connector. Strip the insulation to leave about 3/8″ to 1/2″ bare wire.

How to wire a computer power supply to a car stereo?

How to wire a computer power supply to a car stereo Using an ATX (desktop computer) power supply for a car stereo isn’t hard – in fact, you only need a few steps: Power connections: Cut a +12V wire (yellow) and a ground (black) wire from the main connector. Strip the insulation to leave about 3/8″ to 1/2″ bare wire.

How do you hook up a car radio to power?

1 Ground: Connect the radio’s ground wire (black wire) to the (-) power supply output 2 Main power: Connect the radio’s +12V battery wire (usually the yellow wire) to the (+) power supply output 3 Turning the radio on: You can do this by hardwiring the radio’s accessory wire (usually red) to the +12V battery wire or you can use a switch in between.

How do you wire a car AMP to a speaker?

Disconnect or cut the factory speaker wires and connect the new wires directly to each speaker terminal. It is important that you keep the polarity of your speaker wiring straight. This means that each positive terminal of the amp connects to a positive terminal of a speaker — and the same goes for the negative terminals.

How to connect an amplifier to a 12-V+ wire?

Use a pair of wire cutters to snip the wire right next to the connector. Repeat the process with one of the COM wires as well. Usually, the 12 V+ wire is yellow or red, but it may vary depending on your power supply. You can choose any 4-pin peripheral connector to use for your amplifier.

How to connect a car amplifier to a car?

Once you’ve connected the +12V and ground wiring then ground the “supply on” wire the supply should start up and your car amplifier should power on. There are some cases where you could have a problem, however. NOTE: If you’re using a high amount of current be sure to use all or nearly all of the yellow +12V wires to connect to the amp.

Can I use a computer power supply for a car AMP?

Using an ATX (desktop computer) power supply for a car amp isn’t hard usually. It’s a matter of a few steps: Power connections: Cut several ground wires (black) and +12V wires (yellow) and strip them for about 3/8″ to 1/2″ bare wire.

How do you connect a 12 volt battery to a car radio?

Power connections: Cut a +12V wire (yellow) and a ground (black) wire from the main connector. Strip the insulation to leave about 3/8″ to 1/2″ bare wire. Use a crimp connector, solder, or another connector type to join the power supply’s +12V output (yellow) to the radio’s +12V battery wire (yellow).

Related posts: