Hook up keg co2 tank

hook up keg co2 tank

How do you hook up a CO2 regulator to a keg?

Attach the gas line to the CO2 regulator output barb and tighten screw clamp. Connect the other end of the gas line to the keg coupler and tighten screw clamp. Using a rubber washer and nut, attach the CO2 regulator to the CO2 tank.

How do you connect a gas kegerator to a beer line?

Connect Beer and Gas Lines Youll need two lines to set up your kegerator - the beer line and the gas line. The beer line connects to the keg by way of the keg coupler and delivers cold beer to the tap faucet. The gas line connects to the CO2 regulator on the CO2 tank, then also connects to the keg coupler.

How many kegs can I dispense in a CO2 tank?

CO2 tank, you can dispense 2 to 4 full-sized kegs before having to refill. The cooler the ambient temperature, the closer you’ll get to 4 kegs.

What do I need to set up a kegerator?

Youll need two lines to set up your kegerator - the beer line and the gas line. The beer line connects to the keg by way of the keg coupler and delivers cold beer to the tap faucet. The gas line connects to the CO2 regulator on the CO2 tank, then also connects to the keg coupler.

How do you hook up a CO2 tank to a keg?

Attach the beer line to the keg coupler, placing a rubber washer at the connection point. Attach the gas line to the CO2 regulator output barb and tighten screw clamp. Connect the other end of the gas line to the keg coupler and tighten screw clamp. Using a rubber washer and nut, attach the CO2 regulator to the CO2 tank.

How do I connect the gas line to the keg coupler?

Follow these steps: 1 Keep the tank upright at all times. 2 Attach the beer line to the keg coupler, placing a rubber washer at the connection point. 3 Attach the gas line to the CO2 regulator output barb and tighten screw clamp. 4 Connect the other end of the gas line to the keg coupler and tighten screw clamp. More items...

What do I need to set up a kegerator?

Youll need two lines to set up your kegerator - the beer line and the gas line. The beer line connects to the keg by way of the keg coupler and delivers cold beer to the tap faucet. The gas line connects to the CO2 regulator on the CO2 tank, then also connects to the keg coupler.

What does a CO2 regulator do in a kegerator?

A regulator is an essential part of a kegerator dispense system and monitors your CO2 pressure. You can find single gauge regulators or dual gauge regulators, which connect to the air line and read the pressure. With a single gauge regulator, the display will show you your CO2 pressure.

draft beer faqs. How many kegs of draft beer can be dispensed out of a CO2 tank? As a general rule of thumb, it takes about a 1/2 lb of CO2 to dispense a 1/4 barrel of draft beer and 1 lb of CO2 to dispense a 1/2 barrel of draft beer.

What size CO2 tank do I need to carbonate beer?

How do you open a kegerator keg?

Once the coupler is in place press down on the lever to open the keg up. See our detailed instructions on how to tap a keg. Grab the kegerator faucet and faucet wrench (usually provided) and insert the wrench into the holes on the faucet collar.

How to maintain a kegerator?

Now that your kegerator is in place and ready to use, set up a schedule to maintain your beer system and ensure your taps and beer lines stay clean. Inspect the CO2 levels on your tank regularly and check the PSI gauge to make sure the pressure is at the right level.

What tools do I need to install a keg regulator?

Screw clamps can be used to fasted both beer and air line connections to ensure no liquid or compressed air is escaping the system as it works. The nylon washers are specifically built for creating a tight seal between your CO2 regulator and compressed air tank. A flathead screwdriver is also needed, depending on the keg regulator youre using.

How do you install a draft tower on a kegerator?

To install the draft tower, line up the circular gasket holes to the screw holes on top of the kegerator fridge. Feed the vinyl beer line all the way through the opening, and then screw in the tower screws through the gasket and holes atop the keg fridge. Step 3: Attach tap faucet.

Related posts: